aboutsummaryrefslogtreecommitdiffstats
path: root/Alc/mixer.c
Commit message (Collapse)AuthorAgeFilesLines
* Reorder some parameters for consistencyChris Robinson2010-11-291-1/+1
|
* Store double formats as floatChris Robinson2010-11-281-46/+0
| | | | | The mixer will cut it down to float anyway, so it's unnecessary and needlessly creates more mixer functions
* Rename some stuff for consistencyChris Robinson2010-11-281-3/+3
|
* Don't store the internal format in the bufferChris Robinson2010-11-281-1/+1
| | | | The type and channel config are good enough
* Support rear formats directly in the mixerChris Robinson2010-11-271-0/+23
|
* Support 64-bit double buffers directlyChris Robinson2010-11-271-0/+42
|
* Use enums when selecting the mixerChris Robinson2010-11-261-29/+34
|
* Avoid some more code duplicationChris Robinson2010-11-261-36/+44
|
* Properly clamp high pitch valuesChris Robinson2010-11-261-17/+0
|
* Subtract the fractional position separatelyChris Robinson2010-11-261-1/+2
|
* Rename some variables to be clearerChris Robinson2010-11-261-61/+62
|
* Make the buffer padding size dependent on the resamplerChris Robinson2010-11-261-15/+20
|
* Convert a few divisions to multiplicationsChris Robinson2010-11-261-6/+7
|
* Make a FRACTIONONE macro, and use itChris Robinson2010-11-261-8/+8
|
* Share the interpolation functions and use them in the reverb effectChris Robinson2010-11-261-23/+9
|
* Add a missing break statementChris Robinson2010-11-251-0/+1
|
* Add a cubic resamplerChris Robinson2010-11-251-6/+57
|
* Force the point resampler when the source plays at normal speedChris Robinson2010-11-251-1/+1
|
* Pass a pointer to the samplers so they can read just the samples they needChris Robinson2010-11-251-64/+51
|
* Add "pre-padding" to the temp bufferChris Robinson2010-11-251-10/+88
| | | | This will help to implement resamplers that want previous samples
* Make sure the target buffer size is frame alignedChris Robinson2010-11-251-0/+1
|
* Minor rework of the template macrosChris Robinson2010-11-251-47/+54
|
* Remove the cosine resamplerChris Robinson2010-11-251-44/+0
| | | | It's too slow when auxiliary sends are being used.
* Double-up the interpolation functions (and make them use doubles)Chris Robinson2010-11-251-65/+46
|
* Rename some "template" functionsChris Robinson2010-11-251-21/+21
|
* Always make sure there's a sample available to mix, for pending click removalChris Robinson2010-11-251-109/+53
|
* Use a temporary stack buffer to store the source buffer data to be mixedChris Robinson2010-11-251-72/+150
| | | | | | | | This makes it much easier to pack the playable buffer data so that it's a continuous data stream. This could normally be broken up otherwise, such as when using loop points or small queued buffers. Currently it defaults to a 16KB stack buffer, but this can be overridden at compile time.
* Use 0-based access for the buffer dataChris Robinson2010-11-241-10/+15
|
* Support 8-bit sample data in the mixerChris Robinson2010-11-241-1/+58
|
* Check the sample byte size after the resamplerChris Robinson2010-11-241-66/+51
|
* Get rid of a useless unionChris Robinson2010-11-241-12/+8
|
* Change the mixer macros to declare functionsChris Robinson2010-11-241-76/+196
|
* Set mixer sample pos and frac when neededChris Robinson2010-11-241-6/+12
|
* Reorder some stored source paramsChris Robinson2010-11-241-3/+3
|
* Make sure the buffer padding is always cleared before looking for the next ↵Chris Robinson2010-11-241-2/+1
| | | | buffer
* Avoid temporary float variablesChris Robinson2010-11-211-6/+6
|
* Pass the data pointer and proper sampler to the mixer macroChris Robinson2010-11-211-39/+39
|
* Move aluMixData back to ALu.cChris Robinson2010-11-211-220/+0
|
* Use the number of sends the device is configured for in more placesChris Robinson2010-11-061-3/+3
|
* Use a switch to select the appropriate channel-count mixerChris Robinson2010-11-061-7/+16
|
* Declare a variable where it's usedChris Robinson2010-11-011-2/+1
|
* Fix fpu state handling with _controlfpChris Robinson2010-10-151-3/+2
|
* Check resampler mode first when selecting the mixerChris Robinson2010-09-261-59/+43
|
* Get a variable where it's neededChris Robinson2010-09-261-3/+1
|
* Pass the device to the mix function and localize the dry mix and click buffersChris Robinson2010-09-261-16/+25
|
* Clarify a checkChris Robinson2010-09-261-1/+1
|
* Make the SourceMix function a method of the ALsource structChris Robinson2010-09-261-8/+5
|
* Avoid updating the source in MixSourceChris Robinson2010-09-251-10/+11
|
* Convert shorts so that 0 remains 0Chris Robinson2010-09-251-4/+4
|
* Avoid some code duplicationChris Robinson2010-09-251-96/+44
|
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-26 01:14:43 +0000